Empower With MathPower

Empower With MathPower

Tuesday, November 1, 2011

One Of The Many Uses Of Carbon Nanotubes


COMPUTING

More Efficient Space Engine Uses Carbon Nanotubes

Nanotubes promise better ion-propulsion efficiency.
  • TUESDAY, DECEMBER 8, 2009
  • BY BRITTANY SAUSER
Ion-propulsion systems have propelled a handful of Earth-orbiting and interplanetary spacecraft over the past 50 years. Now researchers at Georgia Institute of Technology are developing more efficient ion thrusters that use carbon nanotubes for a vital component.
Ion propulsion works by accelerating electrically charged, or ionized, particles to propel a spacecraft. One of the most common ion engines, known as a "Hall Effect" thruster, ionizes gas using electrons trapped in a magnetic field. The resulting ions are then accelerated using the potential maintained between an anode and a cathode. But some of the emitted electrons must also be used to neutralize the ions in the plume emitted from the spacecraft, to prevent the spacecraft from becoming electrically charged. Existing Hall Effect thrusters must use about 10 percent of the spacecraft's xenon gas propellant to create the electrons needed to both run the engine and neutralize the ion beam.
The Georgia Tech researchers created a field emission cathode for the thruster using carbon nanotubes. In this type of cathode, electrons are emitted after they tunnel through a potential barrier. The carbon nanotube design is especially efficient because nanotubes are incredibly strong and electrically conductive. "By using carbon nanotubes, we can get all the electrons we need without using any propellant," says Mitchell Walker, principal investigator of the project and an assistant professor in the High-Power Electric Propulsion Laboratory at Georgia Tech. This means that 10 percent more of the ion thruster's propellant is available for the actual mission, extending a spacecraft's lifetime.
"We can pull the electrons from the tip of the material at less than .25 volts per micron," which makes for a tremendously efficient system, says Jud Ready, coprincipal investigator of the project. In contrast, the hollow cathodes conventionally used in ion thrusters require heavy electronics and need to be heated to thousands of degrees to obtain the ample voltage.
Advertisement
Furthermore, since the nanotubes are thin and lightweight, they can be applied to the surface of the thruster body, potentially allowing the spacecraft to carry larger payloads and fit on smaller launch vehicles. Walker presented a paper on the new cathode earlier this year at the Joint Propulsions Conference and Exhibit in Denver and says the new system could be ready to launch in three to five years.
Print

Wood Chips Into Sugar ?


ENERGY

Use of Supercritical Water Could Cut Costs for Ethanol

A startup says it can make sugar for biofuel from wood chips at a fraction of the normal cost.
  • WEDNESDAY, NOVEMBER 2, 2011
  • BY KEVIN BULLIS
Renmatix, a startup based in Kennesaw, Georgia, is using water at high pressure and temperature to transform wood chips into sugar, which can then be fermented to make biofuels and other chemicals. The company says the process can produce sugar for the same price as making it from sugarcane, which has led to profitable biofuels production in Brazil.
Renmatix is addressing the most difficult step in producing ethanol from abundant, cellulosic materials such as wood chips, instead of from corn or sugar crops. Once the sugar is made, the same technology employed in a conventional corn or sugar cane ethanol plant can be used to produce ethanol.
So far, Renmatix has only demonstrated the technology on a small scale, using a facility that can process three tons of wood chips a day. As with all advanced biofuels companies, one of the biggest challenges will be convincing investors to hand over the money needed to build a larger commercial facility to prove the venture is commercially viable. The U.S. Environmental Protection Agency has been forced to waive requirements for cellulosic ethanol because commercial plants for converting cellulosic material to ethanol haven't yet been built. By lowering the cost of producing sugar from cellulosic materials, Renmatix hopes to at last break this logjam.
Researchers and companies have tried many methods of turning cellulose into sugar. Some involve breaking the biomass down using acids or specially tailored enzymes. Others involve using heat and pressure to turn biomass into hydrogen and carbon monoxide, which can be converted to biofuel using inorganic catalysts. Each method has drawbacks: enzymes are expensive; acids are toxic; both processes are slow, and they require expensive equipment. The processes that use high heat and inorganic catalysts also have relatively low yields of the desired fuels.
Advertisement
Instead of using enzymes or acids, Renmatix employs supercritical water—water at very high temperatures and pressures. Under these conditions, cellulose will dissolve and very quickly break down into sugar molecules. The reactions take seconds, compared to days for some other processes. Because of the high speed of the reaction, a relatively small amount of equipment can produce a large amount of sugar, keeping capital costs down. Smaller equipment could also make it possible to distribute the production of biofuels, thereby decreasing the cost of transporting biomass.
Print

Light Sheets


Lighting Sheets Made of Tiny LEDs

Nth Degree Technologies plans to replace bulbs with lights that can be printed on large, flexible surfaces.
  • FRIDAY, OCTOBER 28, 2011
  • BY KEVIN BULLIS
A company called Nth Degree Technologies hopes to replace light bulbs with what look like glowing sheets of paper. The company's first commercial product is a two-by-four-foot-square light, which it plans to start shipping to select customers for evaluation by the end of the year.
The technology could allow for novel lighting designs at costs comparable to the fluorescent light bulbs and fixtures used now, says Neil Shotton, Nth Degree's president and CEO. Light could be emitted over large areas from curved surfaces of unusual shapes. The printing processes used to make the lights also make it easy to vary the color and brightness of the light emitted by a fixture. "It's a new kind of lighting," Shotton says.
Nth Degree makes its light sheets by first carving up a wafer of gallium nitride to produce millions of tiny LEDs—one four-inch wafer yields about eight million of them. The LEDs are then mixed with resin and binders, and a standard screen printer is used to deposit the resulting "ink" over a large surface.
In addition to the LED ink, there's a layer of silver ink for the back electrical contact, a layer of phosphors to change the color of light emitted by the LEDs (from blue to various shades of white), and an insulating layer to prevent short circuits between the front and back. The front electrical contact, which needs to be transparent to let the light out, is made using an ink that contains invisibly small metal wires.
Advertisement
The new transparent electrical contact could itself prove important as a replacement for the indium tin oxide (ITO) used in touch screens and other displays. ITO is brittle and can't be printed, so it's not suitable for flexible displays. It can also be expensive, depending on the price of indium.
While the devices the company has made so far are more efficient than incandescent lights, they're not yet as efficient as fluorescent lights. They emit 20 lumens per watt, compared with about 80 lumens per watt for typical overhead fluorescent lights and 65 lumens per watt for compact fluorescents. A 60-watt light bulb from GE gets about 14 lumens per watt.

Monday, October 31, 2011

Math Empowerment For Physicists & Aerospace Engineers


Hello Everyone!

The year is almost coming to an end, and we are plodding away building Math Giants for the future. We are proud of all our students in the San Gabriel Valley.
We hope to be able  to add Inferential Statistics to our roster of classes in March 2012. The trip to Griffiths Observatory is on for the 29 January 2012. Eighty students have signed up, and we will close it out by 15 November 2011. So see us today.

Thanks,

Math Excellence